ibaBM-DP

Bus monitor: Data acquisition on Profibus DP (HarmonizedCode:84733080, ECCN:N, LKZ:DE, AG:N)
Tillverkare: iba-ag
Artikelnr: 13.121001

Bus Monitor DP-Sniffer, bi-directional - Bus monitor for monitoring and analyzing the data traffic between master and slaves

Technical Data:

  • Manufacturer: iba AG
  • Power supply: 24 V DC ±10 % not stabilized, 2-pin connector, clamp-type terminal, screw connection, included in delivery
  • Power consumption: Up to 12 W
  • Rotary switch: Operating modes, device address (in the cascade)
  • Indicators:
    - 4 LEDs for device status
    - 4 LEDs for each PROFIBUS status bus 0 and 1
    - 2 LEDs for Ethernet interface
  • Ethernet: 10/100 Mbit/s, RJ45 socket
  • Further interfaces: USB (for service purposes only)
    -----
    PROFIBUS interfaces:
  • D-Sub connectors: 2x 9-pin (bus 0, bus 1) for 2 drops
  • Data rate: 9.6 kbit/s to 12 Mbit/s
  • DP slaves: 8,(extentable up to 16)
  • Address range of the slaves: 1 to 126
    -----
    ibaNet interface:
  • Number: 1 (e. g. for the connection to ibaPDA)
  • ibaNet protocols:
    - 32Mbit Flex: Sampling time selectable from 0.5 ms (1540 Bytes), data volume dependent on cycle time
    Number of signals: max. 1024 AI (BYTE, INT, WORD, DINT, DWORD, FLOAT, Big/Little Endian) + max. 1024 DI (bits), a total of max. 4060 Bytes
    - 32Mbit (compatibility mode): Sampling time 1 ms
    Number of signals: max 512 AI (BYTE, INT, WORD, DINT, DWORD, FLOAT, Big/Little Endian; up to 1984 Bytes) + max 512 DI (bits)
    - 3Mbit (compatibility mode): Sampling time 1 ms
    Number of signals: max 64 AI (INT or FLOAT) + max 64 DI (bits)
  • Connectors: RX/TX ST connectors(62.5/125 µm), up to 2000m cable length without repeater
    -----
    Operating and environmental conditions:
  • Cooling: Passive
  • Operating temperature: 32 °F to 122 °F (0 °C to 50 °C)
  • Protection class: IP20
  • Mounting: DIN rail, vertical
  • Standards: EMC: IEC 61326-1, FCC part 15 class A
  • Dimensions (width x height x depth):
    2.13 in x 7.40 in x 5.55 in (54 mm x 188 mm x 141 mm),
    incl. DIN rail clip

Remarks:

  • This is a class A product. In a domestic environment this product may cause radio interferences in which case the user may be required to take adequate measures.
  • A duplex FO cable for bi-directional communication with Flex-master (i.e. ibaFOB-D) is required that ibaPDA can use all device features
  • If the device is used to replace the ibaBM- DPM-S, only one fiber optic link is needed

 

Status: on request

 

Kunder som köpte denna köpte också

ibaPADU-S-B4S

10.124000
Data acquisition device: Modular System (HarmonizedCode:84733080, ECCN:N, LKZ:DE, AG:N)

Mounting Angle for PADU-S modular

10.124006
Mounting Angle for PADU-S-Modular System (HarmonizedCode:84733080, ECCN:N, LKZ:DE, AG:N)

ibaNet750-512/2-DO Relais (Closing Contact)

15.145120
Process coupling: Relais output module for ibaNet750
(HarmonizedCode:84733080, ECCN:N, LKZ:DE, AG:N)